Back to overview Guide

How to turn on a Truma heater: the Combi on the CP Plus, step by step

Reading time: 8 min
CampMatic
How to turn on a Truma heater: the Combi on the CP Plus, step by step

First chilly evening in the van, the manual is somewhere under the luggage, and you are standing at the control panel wondering what to press first. A Truma Combi is operated centrally from the digital Truma CP Plus control panel. Once you know the order, switching it on takes less than two minutes.

This guide covers the whole Truma Combi family: the gas-only Combi 4 and 6, the gas/electric 4E/6E and the diesel D4/D4E/D6/D6E. Which version you have is in the vehicle documents or on the heater's type plate. For operating it on the CP Plus it makes little difference. Only the fuel question in step 2 depends on it.

If your vehicle has an older Trumatic S with a control knob on the heater itself, go to Lighting an older Truma heater: the Trumatic S below.

How to turn on a Truma heater, step by step

Step 1: check the 12 V supply

The Truma Combi needs 12 V from the leisure battery for its controls and fan. A quick look at the battery level on the vehicle's control panel does no harm before you first heat up, especially after the vehicle has been parked for a while.

Step 2: make sure there is fuel

Depending on your Combi version, that means:

  • Gas Combi (Combi 4/6 or 4E/6E): the bottle valve in the gas locker must be open. It sounds obvious, but it is the classic reason a heater will not start, especially after a journey with the gas turned off.
  • Diesel Combi (D4/D4E/D6/D6E): enough diesel in the vehicle tank. The heater draws its fuel from the vehicle tank, and the fuel draw stops at a low level so that you can still drive on in the morning. With an almost empty tank, it will not heat well.

Step 3: choose the heating mode and set the temperature on the CP Plus

Now to the control panel. The CP Plus has a rotary/push knob: turn to select, press to confirm.

  • Activate heating: select room heating (the heating symbol).
  • Set the target temperature: for the first evening, 20 °C is a good starting point. Turn, confirm, done.
  • Hot water (optional): if you also want water warm enough for a shower, switch on hot water as well.

Once you confirm, the Combi starts automatically. A short ignition or start-up sound is normal; then the fan starts.

Step 4: wait, and how long it takes

Depending on the starting point, it takes 10 to 30 minutes for the interior to reach the target temperature. A vehicle that has cooled right down overnight takes much longer than one that was only parked briefly. The water in the water heater is warm enough for a shower after about 20 to 30 minutes. The Combi 4 figures in detail: Truma Combi 4 specifications.

Switching on hot water only

The Truma Combi can heat the water heater without room heating. That is useful in summer, when you only want a shower. On the CP Plus, switch on hot water only instead of heating mode. The interior stays unheated; the water heater still heats up. Important: there must be fresh water in the system first (see the next section).

Common mistakes: when the heater won't start

  • No fuel: on the gas Combi the bottle valve is usually closed (or the bottle is empty), on the diesel Combi the tank is almost empty. A very common cause, so check it first.
  • Water tank empty: do not run the water heater without water. Before heating water, fill the fresh water tank and the system, especially after winter, when the vehicle has been drained.
  • Undervoltage: if the leisure battery is too weak, the heater will not start or cuts out. Check the battery level and connect mains hook-up if necessary.
  • Error code on the CP Plus: note the code and look it up in the list of Truma error codes. Remove the cause, then acknowledge the fault with the rotary/push knob. Switching the panel off and on does not clear a gas fault; it locks the heater for 15 minutes. Details: Truma Combi reset: clearing faults.

If that does not solve it, the full troubleshooting guide helps: Truma heater not working? Causes and fixes for every Combi.

VW Grand California

In the VW Grand California the heater works exactly as described above: the control panel is the CP Plus, and the steps are the same. Two things still cause confusion there:

  • Camping mode is not needed for the heater. This is a common misconception. The Truma runs independently of it, so there is nothing to switch over before heating.
  • Two panels, two jobs: the digital control panel in the living area shows levels, battery and solar. You heat on the CP Plus.

Getting more from the CP Plus: the time switch

The CP Plus does more than on and off. With its built-in time switch, the Combi pre-heats automatically in the morning before your alarm goes off. How to set a time window, for example with a lower temperature at night: Running a Truma heater overnight.

Lighting an older Truma heater: the Trumatic S

Many older caravans and motorhomes have no Combi but a gas warm-air heater from the Trumatic S range, for example the S 3002, S 3004, S 5002 or S 5004. It has no CP Plus. You operate it directly on the heater with a control knob that has a built-in thermostat.

Piezo or automatic igniter?

The model name tells you:

  • With a “P” in the name (e.g. S 3002 P, S 3004 P): piezo igniter. You ignite by hand; there is no battery.
  • Without a “P” (S 3002, S 3004, S 5002, S 5004): automatic igniter with a 1.5 V AA battery. It ignites by itself as soon as you press the knob.

The Trumatic S does not need 12 V for ignition. Only accessories such as the Trumavent fan or the lighting need 12 V. The S 2200, the smallest heater in the S range, also has an automatic igniter with a 1.5 V battery. Its operation differs slightly, so follow the appliance's own manual there.

Lighting a Trumatic S, step by step

  1. Turn on the gas: open the gas bottle and the quick-closing valve in the gas supply line.
  2. Turn and press the knob: turn the control knob to the thermostat setting you want (S 3002: 1–10, S 3004: 1–5) and press it down as far as it will go.
  3. Ignite: on the piezo model, press the piezo igniter repeatedly in quick succession at the same time until the flame is lit. The automatic igniter does this by itself, and you can hear the sparks. It keeps going until the flame is lit or you turn the knob to “0”.
  4. Keep it pressed: hold the knob down for up to another 10 seconds so that the flame failure device engages.
  5. Check: watch through the viewing window for a further 10 seconds to see that the flame stays lit.

After a bottle change there is often air in the line. It can then take up to two minutes for gas to arrive. Keep the knob pressed for that long, and keep igniting on the piezo model.

Important: if the flame goes out, wait at least 3 minutes before relighting. Otherwise there is a risk of deflagration. This also applies if a running heater goes out.

The igniter battery

Truma specifies a heat-resistant (+70 °C), leak-proof AA battery (LR 6). Other batteries can cause malfunctions. According to the manual, fit a new battery before every heating season. At the latest, change it when you can no longer hear sparks, or only at intervals of more than one second. Only change it with the heater switched off.

If the Trumatic S won't ignite

  • No gas: bottle or quick-closing valve closed, bottle empty.
  • Air in the line after a bottle change: keep the knob pressed for up to two minutes and keep igniting.
  • Knob released too early: the flame failure device needs up to 10 seconds, otherwise the flame goes out when you let go.
  • Weak battery: no sparks, or only at intervals of more than one second.
  • Snow on the flue or strong wind: clear snow from the flue before starting. If the heater keeps going out in wind, a cowl extension or cowl attachment from Truma helps.
  • Combustion air intake under the vehicle floor dirty or full of slush.
  • Butane in winter: butane no longer vaporises below about 0 °C. Use propane in winter. In the UK, Calor's red bottles are propane, the blue ones butane.

Switching off

Turn the control knob to “0”. This also switches off the automatic igniter. If there is a fan, set its rotary switch to “0”. If you will not use the heater for a while, close the quick-closing valve and the gas bottle.

Good to know: the Trumatic S has no CP Plus and no data bus. So there is nothing an app control could connect to, and CampMatic does not fit it either. CampMatic is made for Truma heaters with a CP Plus (firmware C4 or F4, Vario Heat: P5) or with a Truma iNet X Panel.

The next step: switching the heater on remotely

The CP Plus has one basic drawback: you have to be in the vehicle to use it. No pre-heating on the way, no starting the hot water from the walking trail, no feedback on whether the heater is really running.

That is what CampMatic adds. You control the heater by app, by Telegram or through Home Assistant (MQTT): choose the mode, set the temperature, start the hot water, and read the status and temperature history live. Installation is plug and play: a Y-adapter plugs in directly behind the CP Plus in about 10 minutes, with no tools and no work on the heater. The CP Plus stays fully in place and can still be used. More on the box: CampMatic for Truma CP Plus.

CampMatic fits all compatible Truma heaters, Combi 4/4E/6/6E (gas), D4/D4E/D6/D6E (diesel) and Vario Heat, with CP Plus firmware C4 or F4 (Vario Heat: P5.xx.xx), whatever the vehicle. It has been tested in the VW Grand California, among others. Where to find your version: Finding your Truma CP Plus software version. With a Truma iNet X Panel, take CampMatic for Truma iNet X.

→ CampMatic for Truma CP Plus · WiFi (GC_HW01) — control your heater by app, €149

→ CampMatic for Truma CP Plus · 4G (GC_HW_GSM01) — the same with no WiFi at all, €209

Summary

After the first time, turning on a Truma heater is routine: 12 V supply present, fuel sorted (gas bottle open or enough diesel in the tank), heating mode and target temperature selected on the CP Plus, and 10 to 30 minutes later it is warm. That applies to every Combi version in every vehicle. You light an older Trumatic S directly on the heater: gas on, press the knob, ignite, hold for 10 seconds. And if you want to start the heater from the trail or from bed in future, CampMatic adds remote control in 10 minutes.

Further reading: